Eachine TRASHCAN 75mm Crazybee F4 PRO OSD 2S Whoop FPV Racing Drone Caddx Eos2 Adjustable Camera 25/200mW VTX

Eachine TRASHCAN 75mm Crazybee F4 PRO OSD 2S Whoop FPV Racing Drone Caddx Eos2 Adjustable Camera 25~200mW VTX Swtichable Specifications: Brand Name: Eachine Model Name: TRASHCAN Item Name: 2S 75mm Brushless Whoop racer drone BNF/PNP Wheelbase: 75mm Size: 98mm*98mm*36mm Weight: 33g(without battery) Take off weight:48g(with Original 1s 300mah lipo battery x2) Spare parts specifications: Motor Mode: TC0803 KV15000 Configu-ration: 9N12P Stator Diamter: 8mm Stator Length: 3mm Shaft Diameter: 1mm Motor Dimension(Dia.*Len): 10.5mm*14.5mm Weight(g): 2.2g No.of Cells(Lipo): 1S-2S Flight controller (Frsky version) CRAZYBEEF4 PRO FR Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEEF4 PRO FS Firmware target: CrazybeeF4FS (DSM2/DSMX version) CRAZYBEEF4 PRO Firmware target: CrazybeeF4DX (No RX version) CRAZYBEEF4 PRO FR Firmware target: CrazybeeF4DX MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 3.5-8.7V) Built-in 6A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) DSM2/X Version built-in Serial-based DSM2/DSMX compatible satellite receiver No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection BLHELI_S pass-through Ready Taillight LED Ready Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v) Current: 6A continuous peak 7A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.Hex Default protocol: DSHOT600 Frsky NON-EU receiver Version SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m Flysky receiver Version SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support DSM2/DSMX receiver version Serial bus receiver Protocol: DSM2/DSMX compatible Channels:6-9 (Depend on your radio) No ground interference ( Transmitter and receiver 1 m from the ground): 300m PNP No RX version No RX version support external serial-bus receiver like xm+ crossfire, S-FHSS etc. VTX Output power: 25~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With Raceband Smart Audio ready Weight: 3g CADDX EOS2 camera 1/3" CMOS Sensor 1200 TVL 2.1mm lens 16:9 Image size NTSC Global WDR Internal Synchronization Lipo Battery Capacity: 300mAh Voltage: 3.8v Continuous Discharge Rate: 40C Instantaneous discharge rate: 80C Size: 55mmx11.5mmx6.5mm Weight: 7.8g Connector: PH2.0 *Notes: Need 2pcs batteries for Series circuit Features: PNP version support TBS receiver New Crazybee F4 PRO Flight controller 1-2s Lipo Compatible 2S whoop more powerful and more flight time Betaflight support multi flight mode: ACRO/AIR/ANGLE New 0803 Powerful and High efficiency Brushless motor and Smooth ESC. The motor power with 7V and 40mm propeller can get 55g pull. It is more powerful pull than 0802 49g. Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles(DSMX version no RSSI output) Caddx EOS2 camera ready More comfortable FPV experience Camera Angle adjustable (0-35) VTX power switchable 25mw~200mw Smart Audio ready change VTX bands, powers, channels via OSD Adjust the settings and the PID of the flight controller via OSD Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible Flysky version support both AFHDS and AFHDS-2A protocol transmitter DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter No RX version support external serial-bus receiver like xm+ crossfire, S-FHSS etc.. Full telemetry function ready (Frsky Non-EU and Flysky version support) Support buzzer LED_Strip Ready Real Bind and Fly version Compatible both for 1s-2s User Manual Crazy PNP Manual, Download DSM2 DSMX version Manual, Download Flysky version Manual, Download Frsky version Manual, Download Package Included: PNP/ NO Receiver Version 1 x 75mm Brushless whoop Frame 1 x Crazybee F4 PRO FC no RX verion 4 x TC0803 KV15000 Motor 1 x 40mm propeller(4cw+4ccw) 1 x Caddx EOS2 camera 1 x 5.8G 40ch 25mw~200mw VTX 4 x 3.8v 300mah 40C/80C battery 1 x USB Lipo/LIHV Charger 1 x Propeller disassemble tool 1 x LED board 1 x Screwdriver 1 x XT30 wire 1 x Bag BNF Version 1 x 75mm Brushless whoop Frame 1 x Option1: Crazybee F4 PRO FC built-in Frsky NON-EU receiver Option2: Crazybee F4 PRO FC built-in Flysky AFHDS and AFHDS-2A Switchable receiver Option3: Crazybee F4 PRO FC built-in DSM2/DSMX receiver 4 x TC0803 KV15000 Motor 1 x 40mm propeller(4cw+4ccw) 1 x Caddx EOS2 camera 1 x 5.8G 40ch 25mw~200mw VTX 4 x 3.8v 300mah 40C/80C battery 1 x USB Lipo/LIHV Charger 1 x Propeller disassemble tool 1 x LED board 1 x Screwdriver 1 x XT30 wire 1 x Bag