Wireless Remote Control Switch Universal 433 Mhz Transmitter High Quality Relay Receiver Module

Label:Yes 5.Widely Use: It can connect to the electronic control lock, light, fan, window, curtain, motor, car, lifting appliance, motor control, lifter control or other appliances with DC12V. So that it can remote unlock the door, close the light, open or close the curtain, etc. 3.Strong RF signal, high-sensitive and omnidirectional, you can turn on/off the receiver (not included) by the 433MHz remote control (transmitter) from any place within a reliable distance (150m open area). (The wireless RF signal can pass through walls, floors and doors.). 1.Adopts built-in 1527 working chip, fully compatible with receiving module with common learning code(1527) Chip, such as, PT1527, EV1527, etc. Compatible with the most of 1527 Remote Control Relay Receiver Module, If the remote control is lost, buy one and pair with the receiver is OK.). Coded System: 1527 Learning Code PCB dimension:70*50*25mm Modulation Mode:ASK Matching Mode: Intelligent Learning code Output Mode:Dry contact /Voltage output Features: Frequency Deviation: +0.2MHz or -0.2MHz 4.Easy to install and use, the 4 channel remote control system lets you take control of your gadgets, car and home or garage. Specifications for transmitter: Wireless Operating Distance: 150m(Free Space) Working Voltage: DC 12V Working Current: 12mA 2.Adopts radio frequency technology and stable circuit, high accurate and high-effective, individuation and humanization design, bringing you much convenience. Shell:Yes Working temperature : -30~+80 Working Voltage:DC12V Oscillation Resistance: 340k Working Frequency:433Mhz Specification for receiever: Receiving Sensitivity:-104dBm Color: White Quiescent Current:5mA Size:92*40*15mm Operating RF Frequency: 433MHz Transmitting Power: 10mW Function option:Momentary/Toggle/Latched Transmission Rate: 50 ~ 60KHz Operation Introduction: About Working Mode: 1. Momentary/Joggle: Press and hold- On; Release- Off Keep pressing one button, the corresponding channel is working /on; Release your finger is stop/OFF. (4 channel switch(receiver) need 4 button remote control (transmitter ) 2. Toggle/Self-Lock: Press- On; Press again- Off Press one button for one time, the corresponding channel is working/on; Press the same button again to stop/OFF. (4 channel switch(receiver) need 4 button remote control (transmitter). 3. Latched/Inter-Lock: Press- on; Press other button- Off Press one button for one time, the corresponding channel is working/on; Press another button is stop/OFF(At the same time, another corresponding channel works). (4 channel switch( receiver) need 4 buttons remote control (transmitter). The Setting of Working Mode: 1.Momentary Mode: Pressing the learning key button on the receiver board once (LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote s LED indicator means setting Momentary Mode successfully. 2. Toggle Mode: Pressing two times the learning key button on the receiver board twice(LED Indicator on receiver board will signaling simultaneously),then press any of the remote button , signaling three times by remote s LED means setting Toggle Mode successfully. 3.Latched Mode: Pressing the learning key button on the receiver board three times (LED Indicator on receiver board will signaling simultaneously), then press first remote button, follow on second remote button, signaling three times by remote s LED indicator means setting Latching Mode successfully (first button stands for on, second button stands for off ). 4.2CH Momentary + 2CH Toggle: Pressing the learning key button on the receiver board four times(LED Indicator on receiver board will signaling simultaneously),then press any of the remote button , signaling three times by remote s LED indicator means setting successfully. 5. 2CH Momentary + 2CH Latched: Pressing the learning key button on the receiver board five times(LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote s LED indicator means setting successfully . 6. 2CH Toggle + 2CH Latched: Pressing the learning key button on the receiver board six times(LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote s LED indicator means setting successfully. 7. 2CH Latching + 2CH Latched: Pressing the learning key button on the receiver board seven times(LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote s LED indicator means setting successfully. 8. Deleting Existing Remote Controls Data: Pressing the learning key button on the receiver board eight times, the LED Indicator on receiver board will flash for eight times, it means that the existing remote controls are deleted successfully. Note: 1.This remote control only support the learning code (1527) of the receiver 2.This remote can not be programmed. 3.It will not work if you only buy the transmitter. it is parts of the remote control system, it needs work with the Remote Control Relay Receiver module to achieve controlling. 4. Please do not charged operation, you should shut off the power, and operation after testing and correct electricity. 5. Please promptly change battery when remote control voltage is insufficient (when the battery voltage is insufficient, generally get close transmitting). 6. Please pay attention to avoid metal mask,large equipment,strong interference electromagnetic filed when using wireless RF products, and avoid too short distance between the remote control and receiver board. 7. Please avoid abnormal using of the product.Abnormal using will reduce product performance and life, when seriously it may damage the products and even make danger for your safe. Packaging includes 1pc Receiver/RC (according to your choice)