Diesel Heating 5KW 12V24V Parking Air Fuel Oil Heating Machine Car Fuel Heater For RV, Motorhome Trailer, Trucks Model

Specification: Power: 5000W Voltage: 12V / 24V Fuel Gasoline: Diesel Fuel consumption(L/h): 0.23-0.51 AirFlow: 120-190 Working temperature of the heater: -40~ 76 size: about 39.5*16*38m Weight; Approx 7 Kg Feature: 1.Fast heating ,power saving ,low noise. 2.4 gear power,you can choose the gear you need.Easy to install 3.Independent heating equipment for all types of vehicles and indoor use. 4.Low emissions, low fuel consumption; heater exhaust emissions to meet euro IV engine emissions requirements. Packing List: 1 * Air Heater 1 * Filter 1 * Vent Pipe 1 * Air Outlet Pipe 1 * Intake Pipe 1 * Exhaust Pipe 1 * Fastener 1 * Installation Kit Attention: Not suitable for installation of air heater: 1.Avoid prolonged heating in the living room, garage, non-ventilated weekend homes and hunting lodges to prevent the risk of poisoning from exhaust gases from combustion. It is not allowed to be used in flammable and explosive places with flammable gas and combustible dust. Do not heat and dry the living body (human or animal) avoid heating the article by direct blowing and blowing hot air directly into the container. Filter Installation: 1.When installing the filter element, fill it with oil first and tighten it to prevent air leakage. Tighten the tubing clamp to prevent air leakage, otherwise the combustion effect will be affected. 2.Safety precautions must be taken during installation. For welding and drilling on the car, please refer to the vehicle manufacturer's instructions. Fuel Supply: 1.The plastic fuel tank and fuel injection port must not be located in the cab and passenger compartment. The lid of the plastic fuel tank must be tightened to avoid fuel flow. 2.The supply of wind-heated fuel should be separated from the supply of motor fuel. 3.Must turn off the heater when refueling. 4.It is not allowed to use the oil pump of the vehicle to supply oil to the heater. The oil pump should be installed below the heater. Exhaust Emission: 1. The exhaust gas discharge port must be installed outside the vehicle to prevent the exhaust gas from entering the cab through the ventilation device and the hot air inlet window. 2 .The exhaust gas discharge port must avoid flammable materials and avoid heating the goods to ignite the ground combustibles. 3. During the operation of the heater, the surface of the exhaust pipe will be very hot. It should be kept at a sufficient distance from the heat-sensitive parts, especially the fuel pipes, wires, rubber parts, flammable gas, brake hoses, etc. 4. Exhaust gas emissions are harmful to the human body, prohibiting the heater sleeping in the car during operation. Combustion Inlet: 1.The air inlet must not inhale the combustion air for the heater combustion from the cab. 2.It must absorb the circulating fresh air outside the vehicle to ensure the oxygen supply. 3.Exhaust gases from heaters or other parts of the car must be prevented from entering the combustion inlet system. 4.At the same time, it should be noted that the air intake cannot be blocked by objects. Heating Air Inlet: The air inlet should be equipped with a protective fence to prevent objects from interfering with the operation of the fan. Installation and Repair: 1.Only original accessories are allowed for installation and maintenance. It is not allowed to change the key components of the heater. 2.When connecting the oil pipe, insert the oil nozzle of the oil pump and the oil pipe into the black rubber connecting hose, and there should be a seamless butt joint in the hose to avoid the formation of bubbles in the oil pipeline and affect the combustion effect. Maintenance Instruction: 1.Outside of the heating season, when conditions permit, it is recommended to remove the whole system from the car and keep it properly after cleaning, but never allow the heater host to be separated. 2.It is better to wrap up each tuyere end with plastic bag to prevent sundry enter, cause jam. After a long time idle again before use, to carry out a comprehensive inspection: 1.Check whether the ventilation pipe, combustion air pipe and exhaust pipe are blocked, broken or connected loose. Clean or replace the inner wall when necessary. 2.Check whether the tubing is aged, loose, whether the filter is blocked, and clean or replace it if necessary. 3.Check whether the connection is normal. Incaseof loose binding, corrosion, loosening or fracture of the thread, replacement or treatment shall be carried out. 4.Run on power for 10-20 minutes. If there is a thick fog or abnormal burning sound or obvious smell of fuel for a long time, the heater must be turned off and a professional should be asked to deal with it. Using Tips: During the operation of the heater, it is not allowed to stop the heater by powering off. To increase the service life of the machine, please turn off the switch and wait for the heater to cool down before leaving. If the power is turned off during