Holybro Kakute F4 V2 Flight controller Atlalt HV 25-600mW 40CH VTX Tekko32 35A 4 In 1 Blheli 32 ESC

Holybro Kakute F4 V2 Flight controller Atlalt HV 25-600mW 40CH VTX Tekko32 35A 4 In 1 Blheli 32 ESC Note: The ESC board had chagned to this one with Copper foil. KAKUTE F4 FLIGHT CONTROLLER V2 Specification: MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 5 hardware UARTS (UART1,3,4, 5, 6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x30x8mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g Features Supports Betaflight and Cleanflight. Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles. Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself. New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz. 2 oz. copper PCB allows up to 120A maximum continuous current. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "B+" pad only). Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead. Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip. Supports BLHeli pass-through for easy ESC upgrade and configuration. New V2 Features Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, Monster, etc. Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS. Through-hole solder pads instead of flat pads for more secure soldering especially for beginners. Barometer sensor on board allows altitude hold mode. I2C pad available for certain external sensors. Tekko32 4-in-1 35A ESC Specification: Supports 3-6S lipo input 35A continuous current, 50A burst Mounting holes 30.5x30.5mm Size: 55*40*6.4mm Weight: 17g Feature: 4in1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware. On this version added more CAPS to reduce power noise. 32bit ESC with BLHELI32 firmware 4PWM input Voltage output (VBAT) ESC Telemetry(TELEM) Supports Oneshot / Multishot / Dshot PWM Supports damped light NO BEC Atlatl HV Specification: MCU: STM32F405RGT6 32-bit processor IMU: ICM20689 (SPI) USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 3 hardware UARTS (UART1,3,6) 128 Mbit Dataflash chip for Blackbox logging Dimensions: 35x43x7mm (includes USB in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 7g Feature: Supports Betaflight and Cleanflight. Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles. Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself. New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz. 2 oz. copper PCB allows up to 120A maximum continuous current. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "BAT" pad only). Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead. Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip. Supports BLHeli pass-through for easy ESC upgrade and configuration. To download the installation package of BLHELI_32 Android APP please Click Here. Package Included: 1x Tekko32 4in1 ESC board 1x 8pin to 8pin 1mm pitch cable 1x Kakute f4 +Atlatl stack 1x Heat sink 1x 80mm SMA--MMCX Cable 1x 150mm 4pin JST GH wire